表面涂有防銹油。清潔的汽油或煤油在安裝前必*須仔細清潔，然后涂上清潔的、高質量的或高速的高溫潤滑脂。泰州SKF軸承清潔度對生活和振動和噪音有很大的影響。但我們要特別提醒您，完全關閉不需要清潔和加油。

The surface is coated with anti-rust oil. Clean gasoline or kerosene must be carefully cleaned before installation and then coated with clean, high-quality or high-speed high-temperature grease. Taizhou SKF bearing cleanliness has a great impact on life and vibration and noise. But we would like to remind you in particular that no cleaning and refueling is required for the complete closure.

潤滑對操作和使用壽命有非常重要的影響。簡要介紹了油分離的一般原理。潤滑脂由基礎油、增稠劑和添加劑組成。同類型和牌號的潤滑脂性能差別很大。允許旋轉限*制是不同的。注意選擇是很重要的。泰州SKF軸承潤滑脂的性能主要由基礎油決定。一般來說，低粘度基礎油適用于低溫、高速，高粘度基礎油適用于高溫、高負荷。增稠劑也與潤滑性有關。增稠劑的耐水性決定了潤滑脂的耐水性。原則上，不同牌子的潤滑脂不能混合，甚至同一種增稠劑潤滑脂，由于添加劑不同，會對彼此產生負面影響。

Lubrication has a very important effect on operation and service life. The general principle of oil separation is briefly introduced. Lubricating grease consists of base oil, thickener and additive. Greases of the same type and brand have very different properties. The allowable rotation limit * system is different. It's important to pay attention to choices. The performance of Taizhou SKF bearing grease is mainly determined by base oil. Generally speaking, low viscosity base oil is suitable for low temperature and high speed, and high viscosity base oil is suitable for high temperature and high load. Thickeners are also related to lubricity. The water resistance of the thickener determines the water resistance of the grease. In principle, different brands of grease can not be mixed, or even the same thickener grease, because of the different additives, will have a negative impact on each other.

潤滑時，泰州SKF軸承潤滑油用量越多，效果越好。這是一個普遍的誤解。房間里過多的油和油脂會引起油脂的過度攪拌，導致*極高的溫度。填充潤滑劑的用量應為1/2-1/3，內部空間應填充，高速時應減少到1/3。

When lubricating, the more lubricating oil used in Taizhou SKF bearings, the better the effect. This is a common misunderstanding. Excessive oil and grease in the room can cause excessive stirring of grease, resulting in extremely high temperature. The dosage of filling lubricant should be 1/2-1/3, the inner space should be filled, and it should be reduced to 1/3 at high speed.

安裝時，不要直接接觸端面和非應力表面。使用壓塊、套筒或其*他安裝工具使力均勻。不要通過滾動元件安裝傳動力。如果安裝表面被潤滑，泰州SKF軸承安裝將更加平滑。如果干擾嚴重，應將礦物油加熱至80-90℃，并盡快安裝。嚴格控制油溫不超過100℃，防止硬度降低和尺寸回火的影響。當拆卸遇到困難時，建議您使用拆卸工具進行拆卸，同時小心地在內環上噴灑熱油。熱將擴大內環，使其更容易脫落。

When installing, do not directly contact the end face and non-stress surface. Use a press block, sleeve or its * he installs tools to make the force uniform. Do not install transmission force through rolling elements. If the installation surface is lubricated, the installation of Taizhou SKF bearings will be more smooth. If the disturbance is serious, the mineral oil should be heated to 80-90 C and installed as soon as possible. Strict control of oil temperature not exceeding 100 C to prevent the effect of hardness reduction and size tempering. When disassembly encounters difficulties, it is recommended that you use the disassembly tool for disassembly, while carefully spraying hot oil on the inner ring. Heat will expand the inner ring, making it easier to fall off.

文章來自：泰州SKF軸承 www.wh-skf.com

Article from: Taizhou SKF Bearing www.wh-skf.com

文章來自：泰州INA軸承 www.ina-china.cn

Article from: Taizhou INA Bearing www.ina-China.cn

文章來自：泰州NSK軸承 www.klbbearings.com

Article from: Taizhou NSK Bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757