潤滑脂密封軸承的密封方法是在殼體內預填充適量的泰州INA軸承潤滑脂，在填充間隙內提供潤滑脂。此外，集中潤滑脂供應方法也適用于需要潤滑的多中點推力球軸承。潤滑脂可長期潤滑，不含油脂。該密封裝置結構簡單，應用廣泛。油潤滑相對簡單。

The sealing method of grease seal bearing is to pre-fill the shell with appropriate amount of Taizhou INA bearing grease and provide grease in the filling gap. In addition, the centralized grease supply method is also applicable to multi point thrust ball bearings requiring lubrication. Grease can be lubricated for a long time without grease. The sealing device has simple structure and wide application. Oil lubrication is relatively simple.

向心推力球軸承的安裝與拆卸應根據泰州INA軸承部件的結構、尺寸及匹配特點進行。安裝和拆卸壓力應直接應用于齒圈表面。由于齒圈在軸承工作面上產生凹痕，影響軸承的正常運行，甚至損壞T型軸承，故不能通過滾動體傳遞。軸承保持架、密封圈、防塵罩等零件容易變形，不能承受軸承的安裝或拆卸壓力。軸承的安裝方法如下：

Installation and disassembly of centripetal thrust ball bearings should be carried out according to the structure, size and matching characteristics of Taizhou INA bearing components. Installation and dismantling pressure shall be applied directly to the surface of the gear ring. Because the tooth ring produces dents on the working surface of the bearing, which affects the normal operation of the bearing and even damages the T-type bearing, it can not be transmitted through the rolling element. Bearing cage, sealing ring, dust cover and other parts are easily deformed, and can not withstand the installation or disassembly pressure of bearings. The installation methods of bearings are as follows:

1。軸承外圈與殼體孔緊密配合，內圈與軸松配合。軸承可以首先被壓入殼體中。管的外徑應略小于殼體孔的直徑。

1. The outer ring of the bearing is tightly cooperated with the shell hole, and the inner ring is loosely matched with the shaft. The bearing can first be pressed into the housing. The outer diameter of the tube should be slightly smaller than the diameter of the shell hole.

2。泰州INA軸承內圈與軸、外環和殼孔緊密配合。裝配套的端面應該做成一個環，不僅可以壓.軸承的內圈和外圈，還可以壓.軸承的內圈和外圈，這樣壓力可以傳遞到內圈和外圈，軸承被壓到S.land commu。生產線。這種安裝方法特別適用于自動對準的向心球面軸承的安裝。

2. Taizhou INA bearing inner ring is closely cooperated with shaft, outer ring and shell hole. The end face of the assembly sleeve should be made into a ring, which can not only press the inner and outer rings of the bearing, but also the inner and outer rings of the bearing, so that the pressure can be transmitted to the inner and outer rings, and the bearing is pressed to S. land commu. Production line. This installation method is especially suitable for the installation of centripetal spherical bearings with automatic alignment.

三。軸承內圈與軸緊配合，外環與殼體松配合。泰州INA軸承可以先用壓力機壓在軸承上，然后將軸和軸承裝入殼體中。當軟金屬部件（銅或低碳鋼）被放置在向心推力球軸承的端面上時，它們被擠壓。裝配后，套管的內徑應略大于軸頸直徑，外徑應小于軸承內徑的擋板直徑，以避免對保持架產生壓力。當安裝大量軸承時，手柄可以連接到襯套上。當向心推力球軸承安裝時，軸承孔和軸線的中點線應重合。

Three. The inner ring of the bearing is tightly matched with the shaft, and the outer ring is loosely matched with the shell. The bearing of Taizhou INA can be pressed on the bearing first with a press, and then the shaft and bearing are loaded into the shell. When the soft metal parts (copper or low carbon steel) was placed in the end ball bearing on when they are pressed. After assembly, the inner diameter of the casing should be slightly larger than the Journal diameter, and the outer diameter should be smaller than the baffle diameter of the bearing inner diameter to avoid pressure on the cage. When a large number of bearings are installed, the handle can be connected to the bushing. When the centripetal thrust ball bearing is installed, the midpoint line of the bearing hole and the axis should be coincided.

4。向心推力球軸承的加熱、泰州INA軸承安裝和安裝所需的力與軸承的尺寸和配合干涉的大小有關。對于大、中型軸承大的干擾，常用的熱裝方法。當熱裝時，80-100C軸承或可分離軸承環（不超過100C）在油箱或特殊加熱器中加熱。

4. Heating and centripetal thrust ball bearing Taizhou INA bearing installation and install the required force and the bearing size and the size of interference. For large and medium bearing large interference, commonly used hot charging method. When the hot charging, 80-100C bearings or separable bearing ring (less than 100C) in the heating tank or special heater.

文章來自：泰州SKF軸承 www.wh-skf.com

The article is from: Taizhou SKF bearing www.wh-skf.com

文章來自：泰州INA軸承 www.ina-china.cn

The article is from: Taizhou INA bearing www.ina-china.cn

文章來自：泰州NSK軸承 www.klbbearings.com

The article is from: Taizhou NSK bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672